Self-priming Electric, for Water and Alimentary Fluids | Marco 164 042 1C

£322.00 Price ex.Vat

Available on backorder

02 - 05 units | Per unit: £289.80
06 - 10 units | Per unit: £257.60
11 - 99 units | Per unit: £241.50

Description

Marco 164 042 1C, UPX/AC

Self-priming electric pump for the transfer of liquids of varied nature. The pumping elements are made up of PTFE gears which can possibly even run dry for brief periods. Completely equipped with in-line filter on the inlet side.

Applications

  • Transfer of alimentary fluids
  • Transfer of beverages
  • Transfer of milk
  • Transfer of light alimentary oils.

Fluids Allowed / Not Allowed

There are numerous fields of applications for the pump, however only exclusively with the allowed liquids mentioned:

Fluids Allowed

Water (max 40 °C)
Alimentary Fluids

Warranty expiries if max fluid temperature is exceeded

 Fluids Not Allowed

Petrol (Gasoline) => Danger: Fire / Explosion
Flammable Liquids with PM < 38 °C => Danger: Fire / Explosion
Liquids with viscosity > 20 cSt => Danger: Motor overheating
Corrosive chemical products => Danger: Pump corrosion – Injury to personnel
Solvents => Danger: Fire / Explosion – Damage to seals

Silicone O-rings

Technical Data:

  • Reference: Marco 164 042 1C
  • Voltage: 220V
  • Fuse: A 2
  • Flow rate: l/min 10
    Internal tube Ø 13 mm
  • Pressure: bar 6
  • Weight: 4,6 kg
  • Wire size: (mm2) 0,75
    Length up to 10 m
  • Type: Marco UPX/AC
  • IP 55: Code, International Protection Marking.

PTFE Gear Pumps

Self-priming Electric pumps, for Water and Alimentary Fluids | PTFE Gear Pumps, Marco 164 042 1C, UPX/AC

Self priming electric pumps with helical PTFE gears for the transfer of water and liquids with low viscosity. The PTFE gears guarantee constant pressure, heavy-duty cycles, lower noise levels and excellent resistance to chemicals.

Available in versions with in-line filter, integrated check valve, mechanical pressure switch, electronic pressure sensor and kits for various applications.

Self-priming Electric pumps, for Water and Alimentary Fluids | PTFE Gear Pumps, Marco 164 042 1C, UPX/AC

Nickel-plated brass body, stainless steel shaft and FKM seal unless otherwise specified.

Installation

It is recommended that the use of the pump be according to normative safety standards and also as per the precautions listed below.

 Preliminary Checks:

  • Check that there has been no damage to the pump during transportation or storage.
  • Both inlet and outlet ports should be carefully cleaned removing possible dust or residual packaging material.
  • Verify that the available electrical power supply corresponds to the specification requirements

 Positioning:

  • The pump can be mounted in any position.
  • Fix the pump utilizing suitable diameter screws corresponding to the holes.

Dimensions

Self-priming Electric pumps, for Water and Alimentary Fluids | Dimensions, Marco 164 042 1C, UPX/AC Self-priming Electric pumps, for Water and Alimentary Fluids | Dimensions, Marco 164 042 1C, UPX/AC

Exploded View Diagram

Self-priming Electric pumps, for Water and Alimentary Fluids | Exploded View Diagram, Marco 164 042 1C, UPX/AC

1. Pump body 2. Rubber lip seal 3. Washer 4. Ball bearing 5. Shaft 6. Seeger 7. Flange 8. Washer 9. Screw M 4 x 12 10. Coupling 11. Headless Screw 12. Motor 13. Screw M 5 x 16 14. Idle gear 15. Driving gear 16. Top plate O-ring 17. Top plate 18. Screw 19. Key 20. Tube Outlet 21. O-ring 22. Nipple 23. Filter

Flow Rate Diagram

Self-priming Electric pumps, for Water and Alimentary Fluids | Flow Rate Diagram, Marco 164 042 1C, UPX/AC

Ampere Draw diagram

Self-priming Electric pumps, for Water and Alimentary Fluids | Ampere Draw diagram, Marco 164 042 1C, UPX/AC

About MARCO

MARCO manufacture electric and air horns for cars, trucks and boats, as well as electric pumps for the transfer of various liquids.

These products are manufactured using the most advanced production equipment, such as spectrum analysers, vibrating stands, and other sophisticated instrumentation, including an anechoic chamber, for the development and testing of products.

Today the use of advanced technology enables MARCO to reach the highest International Quality Standards, allowing the creation of highly competitive products that are exported daily to over 80 countries.

Delivery Services

We have a number of Home Delivery services available to you. Availability of these options will be shown at checkout.

International Delivery

We offer delivery to European and many international destinations. For European countries, prices start from £3.00 – €4.00 and are calculated at the checkout page. Click here for a price guide.
For non-European countries, please select your parts and check out normally selecting your country.

Returns

At QuickParts.mobi we hope that you are happy with your purchase, however we know that sometimes you will need to return or cancel an item. Any products returned must be in a re-saleable condition & include the original packing and documentation.

  • Quickparts must be informed of any return requests within 30 days of the original order date.
  • Before returning any goods please read our Terms and Conditions

You’ll find returns information on your delivery note. Unless faulty, we’d like you to make your return within 90 days of purchase. Exceptions apply to certain products – find out more about our refund policy.

Additional information

Weight 4700 g
Dimensions 177 × 165 × 284 mm
Manufacturer

Marco

Reviews

There are no reviews yet.

Be the first to review “Self-priming Electric, for Water and Alimentary Fluids | Marco 164 042 1C”

Your email address will not be published. Required fields are marked *